Planning application
16 Townsend Avenue Seaton EX12 2BE
Permission granted. Work must normally begin within three years of the decision or the permission lapses.
Proposal
Discharge of Condition for 21/1672/FUL: Condition 3 (timber cladding details)
As published by the council, reference 26/0028/DOC
Application record
- Reference
- 26/0028/DOC
- Type
- Discharge of Condition
- Status
- Conditions
- Decision
- Discharge of Condition Approved
- Received
- 7 Jan 2026
- Validated
- 7 Jan 2026
- Decided
- 8 Jan 2026
- Ward
- Seaton
- Parish
- Seaton
- Decision by
- Delegated Decision
- Postcode
- EX12 2BE
Timeline
Dates from the published record
-
7 Jan 2026
Received by East Devon
-
8 Jan 2026
Decision issued: Discharge of Condition Approved
-
26 Jul 2026
Added to PlanIndex
Documents
Plans, drawings, consultee responses and the officer's report
2 documents on file for this application
A planning file usually holds the application form, drawings and site plans, consultee responses, the officer's report and the decision notice.
Trade members open them from here.
Open the documentsWhat this grant of permission means
East Devon granted permission on 8 January 2026, subject to any conditions on the decision notice. Work must normally begin within three years or the permission lapses. More in our guide to what happens after a planning decision.
About condition discharge and variation applications
This application deals with conditions on an existing permission, supplying the details a condition requires or asking to vary or remove one, without reopening the permission itself. More in our guide to planning application types.
Nearby applications
Within 500 metres
-
12 Townsend Avenue Seaton EX12 2BE
93% historically approved · decision due ~30 Sep
Demolish and remove existing rear sun room and rebuild with a greater projection
Awaiting decision Full applications Demolition 14 docs -
3 Townsend Avenue Seaton EX12 2AZ
Proposed single storey rear extension and alterations to rear access and parking area.
Granted Full applications Extension 12 docsSmall domestic -
35 Eyewell Green Seaton EX12 2BN
Proposed single storey rear extension
Granted Full applications Extension 7 docsSmall domestic -
4 Seaton Down Road Seaton EX12 2RZ
Removal of front retaining wall to create parking area and alter entrance ramp to steps to property
Granted Full applications 8 docs -
35, 37 And 39 Seaton Down Road Seaton EX12 2SB
93% historically approved · decision due ~12 Feb
Formation of access and parking and associated hardstandings, creation of pathways and steps and works of wall construction to retain gardens
Awaiting decision Full applications 6 docs -
35, 37 And 39 Seaton Down Road Seaton EX12 2SB
Discharge of conditions for 25/2540/FUL : Condition 3 (materials)
Granted Conditions 3 docs
Other condition discharge and variation applications
In East Devon
-
26/1853/DOC Granted
Chelmer Woodhouse Hill Uplyme Lyme Regis DT7 3SL
Discharge of condition for 25/1842/FUL: Condition 5 (Surface Water Drainage)
-
26/1850/DOC Awaiting decision
6 Potters Close West Hill Devon EX11 1YE
Discharge of condition for 25/1832/FUL: Condition 4 (Trees)
-
26/1833/DOC Awaiting decision
2 Lower Wheathill Sidmouth Devon EX10 9UA
Discharge of condition for 25/2420/FUL: Condition 4 (Tree Protection) and Condition 7 (Materials)
-
26/1845/DOC Awaiting decision
Spout Hill Kilmington Axminster EX13 7RW
Discharge of Condition for 26/1175/LBC: Condition 4a (brick, bedding and pointing mortar details) Bedding Bedding mortar is to be mixed using a well graded washed grit sand (5mm down to 0.075mm) and St Astier NHL 5 at a ratio of 1:2 ? of binder to aggregate by volume. Pointing The pointing mortar is to use a well graded washed aggregate (the largest particle size should not exceed one-third of the joint width) mixed with St Astier NHL5 at a ratio of 1:2 ? of binder to aggregate by volume. Bricks for Chimney Rebuild Reclaimed semi-engineering red brindle brick laid in stretcher bond.
-
26/1841/DOC Awaiting decision
Musbury Garage, Spar Marlborough Road Musbury Devon EX13 8AX
Discharge of condition for 25/1343/FUL: Condition 3 (CMP), Condition 4 (Materials), Condition 7 (Lighting).