Planning application
P/NMA/2025/07363
Cloverdale Court Anning Road Lyme Regis
Proposal
Non-Material Amendment for introduction of new stainless steel vertical supporting columns, similar to that of the original timber supports to the original timber balconies to P/FUL/2024/04606 Reduction in steelwork of the previously proposed balcony design to assist with structural loadings.
As published by the council, reference P/NMA/2025/07363
Timeline
Dates from the published record
-
11 Dec 2025
Received by Dorset
-
29 Jan 2026
Decision issued: Granted
-
26 Jul 2026
Added to PlanIndex
What a grant of permission means
The process from here
Permission has been granted, usually subject to conditions listed on the decision notice, some of which must be discharged before work starts. The decision notice on the council portal sets out exactly what was approved.
Work must normally begin within three years of the decision or the permission lapses. Neighbours cannot appeal a grant; challenging one means judicial review of how the decision was made, within tight time limits.
About amendments applications
How this application type works
An amendment application changes a permission that already exists. Non-material amendments cover small adjustments with no wider effect, while minor material amendments, usually made by varying a condition, allow modest design changes without a fresh application. Anything beyond that needs a new permission, so the scope here is deliberately narrow.
Nearby applications
Within 500 metres
-
P/HOU/2025/05113 Granted
Meadway Charmouth Road Lyme Regis DT7 3DP
Erect a single storey extension at the rear of the property.
-
P/HOU/2022/07225 Refused
Martins Mead Ferndown Road Lyme Regis DT7 3DN
Proposed demolition of existing side and rear extensions/sunroom and construction of two storey rear extension
-
P/CLP/2026/03763 Granted
Cliff Edge East Cliff Lyme Regis DT7 3DH
Demolition of existing shed and garden building. Siting of Shepherd's hut in rear garden, solely for purposes incidental to the enjoyment of the existing dwelling.
-
P/LBC/2026/03667 Awaiting decision
40 Church Street Lyme Regis DT7 3DA
Minor internal works to divide the building into two houses
-
P/FUL/2026/02856 Awaiting decision
Unit 3 Russell House Lym Close Lyme Regis DT7 3DE
Change of use from office/live space E(g)(iii) to 1 bedroom dwelling C3 with minor external alterations
-
P/HOU/2022/07110 Refused
55 Church Street Lyme Regis DT7 3DA
To retain raised decking at rear of garden.
Other amendments applications
In Dorset
-
P/NMA/2026/03502 Refused
Former Perryfield Works Complex Pennsylvania Road Portland DT5 1FJ
Non-material amendment to Approved P/A P/18/00883/FUL (Erect four dwellings) to re-position the existing garages and parking bays
-
P/VOC/2026/04014 Awaiting decision
2 Bonvils Road Worth Matravers BH19 3LR
Erect ground floor extensions and replacement of existing shed to create garden room (with variation of Condition 2 of permission P/HOU/2026/00371 to reduce the scale of the proposal)
-
P/NMA/2026/03363 Granted
Allendale House Hanham Road Wimborne Minster BH21 1AS
Non material amendment to planning permission P/FUL/2025/01489 to revise proposed bollards to the same with LED capping for increased visibility and reinstatement of extra section of walling.
-
P/VOC/2026/02989 Granted
22 Kingston Close Blandford Forum DT11 7UQ
Erect first floor rear extension (With Variation of condition 2 of planning permission P/HOU/2025/01109 to amend approved plans).
-
P/VOC/2026/04024 Awaiting decision
Bulbury Golf Course Bulbury Lane Lytchett Minster BH16 6HR
Erect driving range building and netting( with variation to conditions 2,4 & 6 of planning permission P/FUL/2022/04851 to revise the design for the driving range facility that substantially reduces the overall footprint and massing of the facility. The amendment seeks to reduce the scale of the built structure to eight covered bays, with ball containment instead achieved through a fully netted enclosure surrounding the hitting area, incorporating synthetic turf and net support structures at each corner, and an ancillary ball dispensing unit and a robot holding area with associated hopper.